STAPLES
1010F Series 22 Gauge Upholstery Staples
22 ga · 6–10 mm
Industrial staples for assembly and finishing work. Match the series, crown width and wire cross-section to your stapler before choosing a leg length.
Gauge
22 ga
Length range
6–10 mm
Crown width
11.2 mm
Wire width
0.74 mm
Wire thickness
0.6 mm
Material reference
Zinc-coated wire; grade to confirm
Pieces / strip
134
Availability, material grade, finish and tool compatibility will be checked for the requested configuration and stated in your quotation.
CATALOG REFERENCE DIMENSIONS
Sizes and series
Source-confirmed nominal inch labels are shown where documented. Unverified dimensions remain in the source unit; listed references do not imply every size combination is available.
1010F Series 22 Gauge Upholstery Staples · catalog reference sizes
Reference
Length (mm)
1006F
6 mm / 1/4 in (nominal)
1008F
8 mm / 5/16 in (nominal)
1010F
10 mm / 3/8 in (nominal)
Choose a listed size and include it in your enquiry.
DEFINE THE ORDER, NOT JUST THE FASTENER
Packing, samples and order documentation.
Material and packing details
Parameter
Reference
Standard material reference
Zinc-coated wire
Alternative material enquiry
Stainless steel; specify grade
Fasteners per strip
134
Box / carton packing
Specify the required count; quoted for the selected size
Source feed-wire diameter
0.68 mm before forming
Source point angle
40°
Source zinc-layer reference
0.7–1.0 μm
Material and manufacturing figures are catalog references. Coating thickness is not a batch test result or a corrosion-life guarantee; stainless grade, tool fit and packing are confirmed with the selected size.
APPLICATION EXAMPLES
Where it's used
Explore the materials, joints and workshop tasks below. Match the fastener size and tool to your own workpiece before ordering.
Thin dust-cover attachment
Short-leg fine-wire staples can be evaluated on thin lining over a supported upholstery rail.
Concealed vinyl edges
Check staple seating and breakthrough at thin vinyl-covered fixing margins.
Light decorative panel wrapping
Use the short-leg range as a starting point for thin fabric and limited backing depth.
AI-generated application illustrations, not customer project photographs.
FOUR DIMENSIONS BEFORE A SERIES NUMBER
Read the crown, wire and leg together.
Crown width
Leg length
Wire section
Width × thickness
Measurement guide · schematic, not to scale. Refer to the listed dimensions and an approved order drawing.
1010F Series 22 Gauge Upholstery Staples: check the entire cross-section
A familiar series number helps identify a starting point. The crown width, wire width, wire thickness and leg length determine whether a candidate staple matches the tool and joint.
1. Record the crown width and confirm the supplier’s measurement convention on the order drawing.
2. Record both dimensions of the wire cross-section; gauge alone is insufficient.
3. Choose a listed leg length for the material stack and required penetration.
4. Compare the dimensions with the exact stapler model and approve a sample.
Choose for your workpiece and equipment
01
Identify the short-leg family
This reference is 22GA with 0.74 × 0.6 mm wire and 6–10 mm legs. Select a listed length against covering thickness and usable backing depth.
02
Preserve the surface
Trial crown seating on finished material and inspect for cuts, visible indentations and point breakthrough. A smaller fastener does not eliminate damage from an unsuitable setup.
03
Check the magazine specification
Compare the tool’s fastener drawing, strip profile and accepted lengths with the proposed staple. A 1010F name on a tool is only a starting reference.
Questions before you order
Why select 1010F instead of a longer upholstery staple?
It is a candidate for shallow backing and thin covering assemblies where a short leg meets the attachment requirement. Verify retention on a sample.
Does 22GA identify a compatible staple by itself?
No. Crown, wire width and thickness, leg length and strip geometry must also match.
Application limits to check
- Do not use this fine-wire family as a frame-joining or structural fastener.
- Do not substitute 1022J merely because both list an 11.2 mm crown.
