STAPLES
1022J Series 20 Gauge Industrial Staples
Catalog product reference. See the dimensions below to identify this series.
Jinpai 1022J tool reference. Confirm the actual tool manual and staple geometry.
20 ga · 4–22 mm
Industrial staples for assembly and finishing work. Match the series, crown width and wire cross-section to your stapler before choosing a leg length.
Crown width
11.2 mm / 0.44 in (nominal)
wire width
1.12 mm / 0.044 in (nominal)
wire thickness
0.6 mm / 0.024 in (nominal)
Gauge
20 ga
Length range
4–22 mm
Material reference
Zinc-coated wire; grade to confirm
Pieces / strip
100
Availability, material grade, finish and tool compatibility will be checked for the requested configuration and stated in your quotation.
APPLICATION EXAMPLES
Where it's used
Explore the materials, joints and workshop tasks below. Match the fastener size and tool to your own workpiece before ordering.
Folded upholstery seams
Compare staple seating where a flat covering transitions to a thicker folded seam.
Layered seating-cover edges
Select leg length for the combined cover layers and the receiving seat backing.
Covered arm-panel components
Check attachment at corners and straight sections of the supported upholstery edge.
AI-generated application illustrations, not customer project photographs.
CATALOG REFERENCE DIMENSIONS
Sizes and series
Source-confirmed nominal inch labels are shown where documented. Unverified dimensions remain in the source unit; listed references do not imply every size combination is available.
1022J Series 20 Gauge Industrial Staples · catalog reference sizes
Reference
Length (mm)
1004J
4 mm / 5/32 in (nominal)
1006J
6 mm / 1/4 in (nominal)
1008J
8 mm / 5/16 in (nominal)
1010J
10 mm / 13/32 in (nominal)
1013J
13 mm / 1/2 in (nominal)
1016J
16 mm / 5/8 in (nominal)
1019J
19 mm / 3/4 in (nominal)
1022J
22 mm / 7/8 in (nominal)
On smaller screens, swipe the table to see every column. Confirm the final drawing, tolerances and packaging before ordering.
FOUR DIMENSIONS BEFORE A SERIES NUMBER
Read the crown, wire and leg together.
Crown width
Leg length
Wire section
Width × thickness
Measurement guide · schematic, not to scale. Refer to the listed dimensions and an approved order drawing.
1022J Series 20 Gauge Industrial Staples: check the entire cross-section
A familiar series number helps identify a starting point. The crown width, wire width, wire thickness and leg length determine whether a candidate staple matches the tool and joint.
1. Record the crown width and confirm the supplier’s measurement convention on the order drawing.
2. Record both dimensions of the wire cross-section; gauge alone is insufficient.
3. Choose a listed leg length for the material stack and required penetration.
4. Compare the dimensions with the exact stapler model and approve a sample.
Choose for your workpiece and equipment
01
Compare with the shorter 1010F family
The crown is also 11.2 mm, but this reference uses 1.12 × 0.6 mm wire and 20GA. Matching crown widths do not make the strips interchangeable.
02
Check each required length
The reference spans 4–22 mm; an individual 1022J stapler may accept only a subset. Confirm its minimum as carefully as its maximum.
03
Assess the completed upholstery
Trial on real covering and backing. Inspect cut-through, loose edges, point projection and strip feeding, then retain an approved assembly sample for repeat orders.
DEFINE THE ORDER, NOT JUST THE FASTENER
Packing, samples and order documentation.
Quantity & packing unit
State your quantity in pieces, strips, reels, boxes or cartons. Confirm the conversion between inner packs and shipping cartons.
Samples & minimum order
Send the selected specification and trial quantity. Sample availability, minimum order and lead time will be checked for the requested configuration.
Labels & documentation
Discuss custom packing, private labels and required drawings or documents before order approval. Keep an agreed sample, label and specification reference for repeat orders.
Questions before you order
Is 1022J interchangeable with 1010F?
No. Although both references list an 11.2 mm crown, their wire widths, gauges and length ranges differ.
Should I choose the longest available leg?
Select for the material stack and receiving backing. Excess length can protrude or damage the component; verify retention with the appropriate length.
Application limits to check
- Do not treat 20GA upholstery staples as structural frame fasteners.
- Do not assume every tool with 1022J in its name accepts a 4 mm leg.
