STAPLES
7116 Series 22 Gauge Industrial Staples
Catalog product reference. See the dimensions below to identify this series.
22 ga · 6–16 mm
Industrial staples for assembly and finishing work. Match the series, crown width and wire cross-section to your stapler before choosing a leg length.
Crown width
9.0 mm / 0.35 in (nominal)
wire width
0.75 mm / 0.030 in (nominal)
wire thickness
0.6 mm / 0.024 in (nominal)
Gauge
22 ga
Length range
6–16 mm
Material reference
Zinc-coated wire; grade to confirm
Pieces / strip
100
Availability, material grade, finish and tool compatibility will be checked for the requested configuration and stated in your quotation.
APPLICATION EXAMPLES
Where it's used
Explore the materials, joints and workshop tasks below. Match the fastener size and tool to your own workpiece before ordering.
Narrow seat-cover margins
A 9 mm fine-wire crown can be evaluated where the supported fixing margin is restricted.
Recessed covered-frame edges
Check both the narrow staple crown and tool-nose access at recessed upholstery edges.
Curved chair-back coverings
Trial crown placement around curved concealed edges using the actual upholstery material.
AI-generated application illustrations, not customer project photographs.
CATALOG REFERENCE DIMENSIONS
Sizes and series
Source-confirmed nominal inch labels are shown where documented. Unverified dimensions remain in the source unit; listed references do not imply every size combination is available.
7116 Series 22 Gauge Industrial Staples · catalog reference sizes
Reference
Length (mm)
7106
6 mm / 1/4 in (nominal)
7108
8 mm / 5/16 in (nominal)
7110
10 mm / 3/8 in (nominal)
7112
12 mm / 15/32 in (nominal)
7114
14 mm / 9/16 in (nominal)
7116
16 mm / 5/8 in (nominal)
On smaller screens, swipe the table to see every column. Confirm the final drawing, tolerances and packaging before ordering.
FOUR DIMENSIONS BEFORE A SERIES NUMBER
Read the crown, wire and leg together.
Crown width
Leg length
Wire section
Width × thickness
Measurement guide · schematic, not to scale. Refer to the listed dimensions and an approved order drawing.
7116 Series 22 Gauge Industrial Staples: check the entire cross-section
A familiar series number helps identify a starting point. The crown width, wire width, wire thickness and leg length determine whether a candidate staple matches the tool and joint.
1. Record the crown width and confirm the supplier’s measurement convention on the order drawing.
2. Record both dimensions of the wire cross-section; gauge alone is insufficient.
3. Choose a listed leg length for the material stack and required penetration.
4. Compare the dimensions with the exact stapler model and approve a sample.
Choose for your workpiece and equipment
01
Check the complete 71 reference
This family lists 22GA, 0.75 × 0.6 mm wire and 6–16 mm legs. Match those dimensions to the actual magazine and driver.
02
Check access before ordering
Provide a section drawing or photograph of the recess. Confirm that the tool can sit correctly without marking the finished cover or forcing an angled installation.
03
Test the concealed edge
Inspect cover tension, edge tearing, crown seating and retained movement on a representative assembly. Include corners and any stiff backing layer.
DEFINE THE ORDER, NOT JUST THE FASTENER
Packing, samples and order documentation.
Quantity & packing unit
State your quantity in pieces, strips, reels, boxes or cartons. Confirm the conversion between inner packs and shipping cartons.
Samples & minimum order
Send the selected specification and trial quantity. Sample availability, minimum order and lead time will be checked for the requested configuration.
Labels & documentation
Discuss custom packing, private labels and required drawings or documents before order approval. Keep an agreed sample, label and specification reference for repeat orders.
Questions before you order
Why consider a 9 mm crown for upholstery?
It can suit a restricted fixing margin, provided the material remains securely retained and both legs have adequate backing.
Does this fit every tool marked 71?
Compatibility needs the manufacturer’s fastener drawing and a sample feeding check. Wire dimensions and accepted lengths can differ.
Application limits to check
- A narrow fine-wire crown is not equivalent to an 18GA woodworking staple.
- Do not assume long-nose access from the staple series number.
FROM THE BLOG
